|
 Passage
function: Once the lock is unlocked, the lower lever latch
will remain at unlock position. The top dead bolt and the lower latch
will be locked by pulling the lever handle all the way up from either
side of the lock.
Storeroom function:
Once the lock is unlocked, the lower lever latch will be locked automatically
after closing the door. Free to unlock the lower lever latch from inside
by turning lever. To lock the upper deadbolt and lever latch from outside,
enter correct code and pull the lever up.
Common System Features:
- Cylindrical 1" dead bolt or mortise lock
- Easy to operate - just lift the lever handle to lock and press down
to unlock the door from inside
- Passage or Storeroom functions are available
- Long lasting battery life - 30,000 entries or one to two years of
stand-by life
- Only manager can add or delete code
Specifications:
- Door thickness: 1-3/8" and 1-3/4" (35mm and 45mm)
- Back set 2-3/8" and 2-3/4" (60mm and 70mm)
- Distance between latch and deadbolt: 5" (127mm)
- Latch bolt throw: 1/2" (12.7 mm)
- Deadbolt throw: 1" (25.4 mm)
1. Can I reverse hands?
2. Can I change lock function from passage to storeroom
function?
3. How hard is it to install the lock?
4. If there are 2 cylindrical holes on my door and center
distance is not 5", can I use your locks?
5. Why my burglar alarm sounds?
6. Why does red light will glow?
7. Why do both Red and Green do flashing and Beeper
alarm sounds?
8. How long do we need replace batteries?
9. Can we use chemicals to clean or polish our lock?
10. How can we open the code cover?
11. How can we unlock, If we can not release the lock
by digital keypad?
1. Can I reverse hands?
Yes. Our locks can be reverse left or right by rotate rotor, hands without
disassembling the locks case.
2. Can I change the lock function from passage to storeroom function?
Yes, the unique and simple patented lockset mechanism is flexible to fit
to passage or storeroom. The simple change instruction will be provided
without charge, if requested.
3. How hard is it to install the lock?
It is very easy to install. We provide free charge door preparation jig
and strike position locator to help you to install our locks.
4. If there are 2 cylindrical holes on my door and center to center
distance is not 5", can I use your locks?
Yes. you can purchase a step up deadbolt position gear box at $20, plus
shipping and handling fee. This gear box can help you to install our lock
to different door preparations (center to center holes distance of 4",4.5",5.5"
and 6").
5. Why my burglar alarm sounds?
The burglar alarm will sound when emergency key is used, if the batteries
or electronics are operating normally. The alarm will sound for 10 seconds
and quit for 6 seconds. This cycle will be repeated 8 times.
6. Why does red light will glow?
Red light will glow when a wrong code is entered.
7. why do both Red and Green do flashing and Beeper alarm sounds?
Both Red and Green are flashing indicates that the entry has been attempted
with an incorrect code 3 times. Beeper alarm activates after three incorrect
codes are entered, and blocks further attempts of entry for two minutes.
8. How long do we need replace batteries?
We suggest every two years (for the keypad model), and one year (for the
remote controller model), even if the yellow light does not glow. To remove
the battery housing: insert tool in the pinhole at the center-left of
the inner escutcheon, depress to release and remove the housing, replace
batteries.
9. Can we use chemicals to clean or polish our lock?
Do not use chemicals or abrasive materials to clean the lock.
10. How can we open the code cover?
Insert tool into the pinhole at top right side of the escutcheon and depress
to release code cover.
11. How can we unlock, if we can not release the lock by digital keypad?
You can use Emergency Key in case of battery or electronic failure. The
keyholes is located on the outer escutcheon near the doorjamb side. We
suggest do not use Emergency key as a mechanic override key, please fix
the electronic failure as soon as possible.
|
